| 国际标准: | |
| ISO 2178:1982 |
在磁性基体上的非磁性复盖层--复盖层厚度测量--磁测法 Non-magnetic coatings Ｏn magnetic substrates -- Measurement of coating thickness-Magnetic method |
| ISO 2360:2003 |
在非磁性金属基体上的非导电复盖层--复盖层厚度测量--涡流法 Non-conductive coatings Ｏn non-magnetic electrically conductive basis materials-Measurement of coating thickness- Amplitude-sensitive eddy current method |
| ISO 2361-82E | 磁性和非磁性基体上镀镍层厚度的磁性测量方法(NDT,87-2) |
| ISO 2361:1982 |
在磁性和非磁性基体上的电镀层--镀层厚度测量--磁测法 Electrodeposited nickel coatings Ｏn magnetic and non-magnetic substrates-Measurement of coating thickness -- Magnetic method |
| ISO N 237 | 铸钢件的磁粉探伤 |
| ISO 3059:2002 | 无损检测 渗透检验和磁粉检验 观察条件 黑光源的间接评定方法（TC135） |
| ISO 4309-1981 | 起重机械用钢丝绳检验和报废实用规范 |
| ISO5065/ 1 | 磁粉检验指示器-第1部分:特性 |
| ISO5065/ 2 | 磁粉检验指示器-第2部分:试验 |
| ISO DP 5578 | 磁粉检验用磁化设备 |
| ISO 4986:1992 |
钢铸件-磁粉检验 Steel castings-Magnetic particle inspection |
| ISO 6933:1986 |
铁道轧材--磁粉验收试验 Railway rolling stock material -- Magnetic particle acceptance testing |
| ISO 9302:1994 |
无缝和焊接( 埋弧焊除外) 承压钢管--验证液压密封性的电磁检验 Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes-Electromagnetic testing for verification of hydraulic leak-tightness |
| ISO 9304:1989 |
无缝和焊接( 埋弧焊除外) 承压钢管--探测缺陷的涡流检验 Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes-Eddy current testing for the detection of imperfections |
| ISO 9402:1989 |
无缝和焊接( 埋弧焊除外) 承压钢管--探测铁磁性钢管纵向缺陷的全圆周磁传感器/ 漏磁检验 Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes-Full peripheral magnetic transducer/flux leakage testing of ferromagnetic steel tubes for the detection of longitudinal imperfections |
| ISO 9598:1989 |
受压无缝钢管 探测铁磁性钢管横向缺陷的全圆周磁传感器/ 漏磁检验 Seamless steel tubes for pressure purposes-Full peripheral magnetic transducer/flux leakage testing of ferromagnetic steel tubes for the detection of transverse imperfections |
| ISO 9934-1:2016 |
无损检测--磁粉检测--第1部分:总则 （GB/T 15822.1-2005 IDT） Non-destructive testing-Magnetic particle testing-Part 1: General principles |
| ISO 9934-2:2002 |
无损检测--磁粉检测--第2部分:检测介质 （GB/T 15822.2-2005 IDT） Non-destructive testing-Magnetic particle testing-Part 2: Detection media |
| ISO 9934-3:2002 |
无损检测--磁粉检测--第3部分:设备 （GB/T 15822.3-2005 IDT） Non-destructive testing-Magnetic particle testing-Part 3: Equipment |
| ISO 10893-2:2011 |
钢管无损检测 第2部分：无缝钢管和焊接(埋弧焊除外)钢管缺欠的自动涡流检测 适用于外径不小于4mm的无缝和焊接管的自动涡流检测(埋弧焊管除外) |
| ISO 10893-3:2011 |
无缝和焊接(埋弧焊除外)铁磁性钢管纵向和/或横向的缺欠的自动全周漏磁检测 适用于外径不小于10mm的铁磁性无缝和焊接钢管的全周自动漏磁检测 |
| ISO 10893-5:2011 |
钢管无损检测 第5部分：无缝钢管和焊接钢管表面缺欠的磁粉检验 适用于无缝钢管和焊接钢管表面缺欠的磁粉检测，包括钢管内外表面及端面的检测 |
| ISO 12707:2016 |
无损检测--磁粉检测--词汇 Non-destructive testing-Magnetic particle testing-Vocabulary |
| ISO 12718:2008 |
无损检测--涡流检测--词汇 Non-destructive testing -- Eddy current testing --Vocabulary |
| ISO 13664:1997 |
无缝和焊制承压钢管 管端分层缺陷的磁粉检测 Seamless and welded steel tubes for pressure purposes-Magnetic particle inspection of the tube ends for the detection of laminar imperfections |
| ISO 13665:1997 |
无缝和焊制承压钢管 管体表面缺陷的磁粉检测 Seamless and welded steel tubes for pressure purposes-Magnetic particle inspection of the tube body for the detection of surface imperfections |
| ISO 15548-1:2013 |
无损检测--涡流检验设备--第1部分：仪器特性与 验证 Non-destructive testing -- Equipment for eddy current examination -- Part 1: Instrument characteristics and verification |
| ISO 15548-2:2013 |
无损检测--涡流检验设备--第2部分：探头特性与 验证 Non-destructive testing -- Equipment for eddy current examination -- Part 2: Probe characteristics and verification |
| ISO 15548-3:2008 |
无损检测--涡流检验设备--第3部分：系统特性与 验证（GB/T 14480.3-2008 IDT） Non-destructive testing -- Equipment for eddy current examination -- Part 3: System characteristics and verification |
| ISO 15549:2008 | 无损检测--涡流检验--总则 Non-destructive testing -- Eddy current testing --General principles |
| ISO 17638:2003 | 焊缝无损检测--磁粉检测 Non-destructive testing of welds-Magnetic particle testing |
| ISO 17643:2005 | 焊缝无损检测--利用复平面分析的涡流检测 Non-destructive testing of welds-Eddy current testing of welds by complex-plane analysis |
| ISO 20339:2017 | 无损检测--涡流检验--阵列探头特性与验证 Non-destructive testing -- Equipmen for eddy current examination -- Array probe characteristics and verification |
| ISO 20669:2017 |
无损检测-铁磁性金属构件的脉冲涡流检测 Non-destructive testing -- Pulsed eddy current testing of ferromagnetic me |
| ISO 23278:2006 | 焊缝无损检测--焊缝的磁粉检测--验收等级 |
| ISO 24497-1 | 无损检测--金属磁存储器-第1部分:一般要求 |
| ISO 24497-2 | 无损检测--金属磁存储器-第2部分:术语与定义 |
| ISO 24497-3 | 无损检测--金属磁存储器-第3部分:焊缝的检验 |
| ISO 25902-1 | 钛管无损检测--第1部分:涡流检验 |
| 欧洲标准化委员会标准： | |
| EN 1290:1998 |
焊缝无损检测 焊缝的磁粉检验 Non-destructive examination of welds-Magnetic particle examination of welds |
| EN 1291:1998 |
焊缝无损检测 焊缝的磁粉检验 验收等级 Non-destructive examination of welds-Magnetic particle testing of welds-Acceptance levels |
| EN 1330-5:1998 |
无损检测 术语 第5部分：涡流检测所用术语 Non-destructive testing-Terminology-Part 5:Terms used in Eddy current testing |
| EN 1330-7:2005 |
无损检测 术语 第7部分：磁粉检测所用术语 Non-destructive testing - Terminology - Part 7: Terms used in magnetic particle testing |
| EN 1369:1996 | 铸件磁粉检查 |
| EN 1711:2000 |
焊缝无损检测 基于复平面分析的焊缝涡流检测 Non-destructive examination of welds-Eddy current examination of welds by complex plane analysis |
| EN 1956: | 无损检测 渗透检测和磁粉检测 |
| EN 1971: | 铜和铜合金的涡流检测 |
| EN 2857/1: | 磁粉检测 总则 |
| EN 2857/2: | 检查要求 |
| EN ISO 3059:2001 |
无损检测 渗透检测和磁粉检测 观察条件 Non-destructive testing-Penetrant testing and magnetic particle testing-Viewing conditions(ISO 3059:2001) |
| EN ISO 9934-1:2001/A1:2003 |
无损检测 磁粉检测 第1部分：总则 Non-destructive testing-Magnetic particle testing-Part 1:General principles(ISO 9934-1:2003) |
| EN ISO 9934-2:2002 |
无损检测 磁粉检测 第2部分：探测介质 Non-destructive testing-Magnetic particle testing-Part 2:Detection media(ISO 9934-2:2002) |
| EN ISO 9934-3:2002 |
无损检测 磁粉检测 第3部分：设备 Non-destructive testing-Magnetic particle testing-Part 3:Equipment(ISO 9934-3:2002) |
| EN 10228/1:1999 | 磁粉检查 |
| EN 10246/1:1996 | 无缝与焊接（埋弧焊除外）铁磁性钢管的自动电磁检测-验证液压密封性 |
| EN 10246/2:2000 | 无缝与焊接（埋弧焊除外）奥氏体和奥氏体铁素体钢管的自动涡流检测-验证液压密封性 |
| EN 10246/3:1999 | 无缝与焊接（埋弧焊除外）钢管的自动涡流检测-探伤 |
| EN 10246/4:1999 | 无缝铁磁性钢管的自动全圆周磁传感器/漏磁检测-检测横向缺陷 |
| EN 10246/5:1999 | 无缝与焊接（埋弧焊除外）铁磁性钢管的自动全圆周磁传感器/漏磁检测-检测纵向缺陷 |
| EN 10246/12:2000 | 无缝与焊接铁磁性钢管的磁粉检测-检测表面缺陷 |
| EN 10246/18:2000 | 无缝与焊接铁磁性钢管管端面的磁粉检测-检测层状缺陷 |
| EN 12084:2001/A1:2003 |
无损检测 涡流检测 一般原理和指南 Non-destructive testing-Eddy current testing-General principles and guidelines |
| EN ISO 12718:2008 |
无损检测 涡流检测 词汇 Non-destructive testing - Eddy current testing - Vocabulary (ISO 12718:2008) |
| EN 13860-1:2003 |
无损检测 涡流检测 设备性能与验证 第1部分：仪器性能与验证 Non-destructive testing-Eddy current examination-Equipment characteristics and verification-Part 1:Instrument characteristics and verification |
| EN 13860-2:2003 |
无损检测 涡流检测 设备性能与验证 第2部分：探头性能与验证 Non-destructive testing-Eddy current examination-Equipment characteristics and verification-Part 2:Probe characteristics and verification |
| EN 13860-3:2003 |
无损检测 涡流检测 设备性能与验证 第3部分：系统性能与验证 Non-destructive testing-Eddy current examination-Equipment characteristics and verification-Part 3:System characteristics and verification |
| EN ISO 15548-1:2008 |
无损检测 涡流检验设备 第1部分：仪器特性与验证 Non-destructive testing - Equipment for eddy current examination - Part 1:Instrument characteristics and verification (ISO 15548-1:2008) |
| EN ISO 15548-1:2008/AC:2010 |
无损检测 涡流检验设备 第1部分：仪器特性与验证 技术勘误表 Non-destructive testing - Equipment for eddy current examination - Part 1:Instrument characteristics and verification - Technical Corrigendum 1 (ISO 15548-1:2008/Cor 1:2010) |
| EN ISO 15548-2:2008 |
无损检测 涡流检验设备 第2部分：探头特性与验证 Non-destructive testing - Equipment for eddy current examination - Part 2:Probe characteristics and verification (ISO 15548-2:2008) |
| EN ISO 15548-3:2008 |
无损检测 涡流检验设备 第3部分：系统特性与验证 Non-destructive testing - Equipment for eddy current examination - Part 3:System characteristics and verification (ISO 15548-3:2008) |
| EN ISO 15549:2010 |
无损检测 涡流检测 总则 Non-destructive testing - Eddy current testing - General principles (ISO 15549:2008) |
| EN WI 45:2002 | 涡流检测设备 |
| 美国相关标准 | |
| 日本: | |
| JIS C2501-1998 | 永久磁铁试验方法 Methods of test for permanent magnet |
| JIS G 0565-1992 |
铁磁性材料磁粉检验方法及磁粉显示等级 (INDT,84-2 1982年版) METHOD FOR MAGNETIC PARTICLE TESTING OF FERROMAGNETIC MATERIALS AND CLASSIFICATION OF MAGNETIC PARTICLE INDICATION |
| JIS G 0568-1993 |
钢制产品的环绕线圈法涡流检测 Method for eddy current testing of steel products by encircling coil technique |
| JIS G 0583-2004 | 钢管的涡流检验方法 Eddy current examination of steel pipes and tubes |
| JIS H 0502-1986 |
铜及铜合金管的涡流检测方法 METHOD OF EDDY CURRENT TESTING FOR COPPER AND COPPER ALLOY PIPES AND TUBES |
| JIS H 0505-1975 |
有色金属材料的电阻率及导电率测定方法 Measuring methods for electrical resistivity and conductivity of non-ferrous materials |
| JIS H 0515-1992 | 钛管的涡流检验 Eddy current inspection of titanium pipes and tubes |
| JIS H 0601:62 | 锗的电阻率测定方法 |
| JIS H 0602:95 | 硅单晶及硅薄片的四探针法电阻率测定方法 |
| JIS Z 2314-1991 |
涡流试验仪器性能特性试验方法 Test methods for performance characteristics of eddy current testing instruments |
| JIS Z 2315-1991 |
涡流探伤系统性能特性试验方法 TEST METHODS FOR PERFORMANCE CHARACTERISTICS OF EDDY CURRENT FLAW DETECTING SYSTEM |
| JIS Z 2319-1991 | 漏磁试验方法 Methods for magnetic leakage flux testing |
| JIS Z 2321-1993 | 用于磁粉检测的交流磁轭 AC YOKE MAGNET FOR MAGNETIC PARTICLE TESTING |
| JIS Z 2340:2002 |
磁粉和渗透检验中目视校验计较准方法的确认 Confirmation method of calibration by visual calibration gauge Ｏn magnetic particle and liquid penetrant testing |
| JIS Z 2343-3:2001 |
无损检测 渗透检测 第3部分：参考试块 Non-destructive testing -- Penetrant testing -- Part 3: Reference test blocks |
| JIS Z 8202-5-2000 | 量值和单位 第5部分:电学和磁学 Quantities and units - Part 5: Electricity and magnetism |
| JIS W 1202-1986 |
宇航用涡流法对铝合金热处理测量的电导试验 Electrical conductivity test for measurement of heat treatment of aluminum alloys, eddy current method, for aerospace use |
| JIS W 4031-82 | 宇航用磁粉检验方法 INSPECTION PROCESS OF MAGNETIC PARTICLE FOR AEROSPACE USE |
| NDIS 3101-84 | 涡流探伤装置单项性能的测试及其表示方法 |
| NDIS 3102-84 | 涡流探伤装置综合性能的测试及其表示方法 |
| NDIS 3301-77 | 磁粉探伤用C1型标准试片 |
| NDIS 3404-82 | 漏磁探伤测试方法(INDT,85-3) |
| NDIS 3105-83 | 交流磁轭磁粉检验装置性能与试验方法 |
| NDIS 3403-81 | 表面缺陷检测方法 |
| 德国: | |
| DIN 50470-1980 |
永磁材料的检测 测定磁轭的退磁曲线和永磁导磁率 感应法 Testing of permanent magnet materials; Determination of the demagnetization curve and permanent permeability in a yoke; Inductive method |
| DIN 50472-1981 |
永久磁铁的检测 在工作范围内测定磁通量值 Testing of permanent magnets; determination of the magnetic flux values in the working range |
| DIN 50933-1987 |
用探针式差动测量器测量涂层厚度 Measurement of coating thickness by differential measurement using a stylus instrument |
| DIN 50981-79 | 用磁粉法测量铁素体材料非铁磁性层的厚度 |
| DIN 50984-78 | 用涡流法测量非铁素体母材的非导电层厚度 |
| DIN 50985-77 | 用电容法测量导电母材上非导电层的厚度 |
| DIN 54121-65 | 磁粉探伤定义及检验证明 |
| DIN 54130-1974 |
无损检测 漏磁检测 通则 Non-destructive testing; magnetic leakage flux testing, general |
| DIN 54131T1-84 | 除携带式以外的固定式与移动式磁粉检验设备性能及测定方法 |
| DIN 54131T2-84 | 携带式磁粉检验设备性能及测定方法 |
| DIN 54132-80 | 磁粉检验介质的性能测定 |
| DIN 54136-1-1988 |
无损检测 带扫描探头的漏磁检测 原理 Non-destructive testing; magnetic leakage flux testing by scanning with probes; principles |
| DIN 54140-3-1989 |
无损检测 电磁法 测试线圈组件的图像和一般特性 Non-destructive testing; electromagnetic methods; representation and general characteristics of test coil assemblies |
| DIN 54140T1-76 | 电磁(涡流)法检测的一般规则 |
| DIN 54140T2-84 | 电磁检测名词术语 |
| DIN 54141-1-1982 |
无损检测 管子的涡流检测 用同心试验线圈和单频率法检测的一般注意事项 Non-destructive testing; Eddy current testing of pipes and tubes; General remarks Ｏn testing using concentric test coils and the single-frequency method |
| DIN 54141-2-1982 | 无损检测 管子的涡流检测 同心试验线圈的涡流检测系统性能测定与校验的参考方法 Non-destructive testing; Eddy current testing of pipes and tubes; Reference method for the determination and calibration of the properties of an eddy current testing system using concentric test coils |
| DIN 54141-3-1987 |
无损检测 管子的涡流检测 方法 Non-destructive testing; eddy current testing of pipes and tubes; procedure |
| DIN 54141T1-82 | 穿过式线圈单频法管材涡流检测(NDT,86-1) |
| DIN 54141T2-82 | 穿过式线圈涡流检验装置性能的测定方法 |
| DIN 54141T3-85 | 涡流检测的实施 |
| DIN 25435T2-79 | 核技术设备定期磁粉检验 |
| DIN V VDE V 0848-4/A3-1995 |
电磁场中的安全性 在0至30KHz频率范围的人员防护 修订3 Safety in electromagnetic fields - Protection of persons in the frequency range from 0 to 30 kHz; Amendment A3 |
| DIN EN 1290-2002 |
焊缝的无损检测 焊缝的磁粉检测 Non-destructive testing of welds - Magnetic particle testing of welds; German version EN 1290:1998 A1:2002 |
| DIN EN 1291-2002 |
焊缝的无损检测 焊缝的磁粉检测 验收等级 Non-destructive testing of welds - Magnetic particle testing of welds - Acceptance levels; German version EN 1291:1998 A1:2002 |
| DIN EN 1330-5-1998 |
无损检测术语 第5部分:涡流检测 Non-destructive testing - Terminology - Part 5: Terms used in Eddy Current testing; trilingual version EN 1330-5:1998 |
| DIN EN 1369-1997 | 铸造 磁粉检验 Founding - Magnetic particle inspection; German version EN 1369:1996 |
| DIN EN 1971-1998 |
铜和铜合金 管子的涡流检测 Copper and copper alloys - Eddy current test for tubes; German version EN 1971:1998 |
| DIN EN 1711-2000 |
焊缝的无损检验 焊缝的复平面分析涡流检验 Non-destructive examination of welds - Eddy current examination of welds by complex plane analysis; German version EN 1711:2000 |
| DIN EN 10228-1-1999 |
钢锻件的无损检测 第1部分:磁粉检验 Non-destructive testing of steel forgings - Part 1: Magnetic particle inspection; German version EN 10228-1:1999 |
| DIN EN 10246-1-1996 | 钢管的无损检测 第1部分:验证无缝和焊接铁磁钢管(埋弧焊除外)水压密封性的自动电磁检测 Non-destructive testing of steel tubes - Part 1: Automatic electromagnetic testing of seamless and welded (except submerged arc-welded) ferromagnetic steel tubes for verification of hydraulic leak-tightness; German version EN 10246-1:1996 |
| DIN EN 10246-3-2000 | 钢管的无损检测 第3部分:探测无缝和焊接钢管(埋弧焊接除外)不完整性的自动涡流检测Non-destructive testing of steel tubes - Part 3: Automatic eddy current testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of imperfections; German version EN 10246-3:1999 |
| DIN EN 10246-4-2000 | 钢管的无损检测 第4部分:探测铁磁无缝钢管横向不完整性的自动全圆周磁探头/磁漏检测 Non-destructive testing of steel tubes - Part 4: Automatic full peripheral magnetic transducer/flux leakage testing of seamless ferromagnetic steel tubes for the detection of transverse imperfections; German version EN 10246-4:1999 |
| DIN EN 10246-5-2000 | 钢管的无损检测 第5部分:探测无缝和焊接(埋弧焊接除外)铁磁钢管纵向不完整性的自动全圆周磁探头/磁漏检测 Non-destructive testing of steel tubes - Part 5: Automatic full peripheral magnetic transducer/flux leakage testing of seamless and welded (except submerged arc-welded) ferromagnetic steel tubes for the detection of longitudinal imperfections; German version EN 10246-5:1999 |
| DIN EN 10246-18-2000 | 钢管的无损检测 第18部分:探测无缝和焊接铁磁钢管管端层状不完整性的磁粉检验 Non-destructive testing of steel tubes - Part 18: Magnetic particle inspection of the tube ends of seamless and welded ferromagnetic steel tubes for the detection of laminar imperfections; German version EN 10246-18:2000 |
| DIN EN 12084-2001 |
无损检测 涡流检测 一般原理和基本指南 Non-destructive testing - Eddy current testing - General principles and basic guidelines; German version EN 12084:2001 |
| DIN EN 13860-1-2003 |
无损检测 涡流检验 设备特性和验证 第1部分:仪器特性和验证 Non-destructive testing - Eddy current examination; Equipment characteristics and verification - Part 1: Instrument characteristics and verification; German version EN 13860-1:2003 |
| DIN EN 13860-2-2003 |
无损检测 涡流检验 设备特性和验证 第2部分:探头特性和验证 Non-destructive testing - Eddy current examination; Equipment characteristics and verification - Part 2: Probe characteristics and verification; German version EN 13860-2:2003 |
| DIN EN ISO 2178-1995 |
磁性基体上的非磁性涂镀层 涂镀层厚度测量 磁性法 Non-magnetic coatings Ｏn magnetic substrates - Measurement of coating thickness - Magnetic method (ISO 2178:1982); German version EN ISO 2178:1995 |
| DIN EN ISO 2360-1995 |
非磁性基体金属上的非导体涂层 涂层厚度测量 涡流法 Non-conductive coatings Ｏn non-magnetic basis me |
| DIN EN ISO 2361-1995 |
磁性和非磁性基体上的镍电镀层 镀层厚度测量 磁性法 Electrodeposited nickel coatings Ｏn magnetic and non-magnetic substrates - Measurement of coating thickness - Magnetic method (ISO 2361:1982); German version EN ISO 2361:1995 |
| DIN EN ISO 9934-1-2002 |
无损检测 磁粉检测 第1部分:一般原理 Non-destructive testing - Magnetic particle testing - Part 1: General principles (ISO 9934-1:2001); German version EN ISO 9934-1:2001 |
| DIN EN ISO 9934-2-2003 |
无损检测 磁粉检测 第2部分:探测介质 Non-destructive testing - Magnetic particle testing - Part 2: Detection media (ISO 9934-2:2002); German version EN ISO 9934-2:2002 |
| DIN EN ISO 9934-3-2002 |
无损检测 磁粉检测 第3部分:设备 Non-destructive testing - Magnetic particle testing - Part 3: Equipment (ISO 9934-3:2002); German version EN ISO 9934-3:2002 |
| 英国: | |
| BS 1881-204-1988 | 混凝土试验-电磁式保护层厚度计应用的推荐方法 |
| BS 3680/3H:1993 | 利用线圈全部长、宽的电磁方法 |
| BS 3683-2-1985 |
无损检测术语 磁粉探伤 Glossary of terms used in non-destructive testing - Magnetic particle flaw detection |
| BS 3683 Pt.5-83 | 涡流检测名词术语 |
| BS 3889 Pt.2A-86(1991) | 管道和管子无损检测方法 锻钢管的涡流检测 |
| BS 3889 Pt.2B-82 | 管道和管子无损检测方法 有色金属管的涡流检测 |
| BS 4069-82 | 磁粉探伤用磁粉及磁悬液(INDT,84-2) |
| BS 4080/1: | 用磁粉探伤显示表面缺陷 |
| BS 4397-69 | 焊缝的磁粉检测方法(WSTS,85-4) |
| BS 4408 Pt.1-69 | 混凝土复盖层的电磁测量方法 |
| BS 4489:1984 | 无损检测中评定黑光的方法 |
| BS 5044-73(1987) | 磁粉探伤用反差增强涂料 |
| BS 5138-74(2000) | 精加工整体锻造及落锤锻曲轴的磁粉检验 |
| BS 5411 Pt.3-84 | 非磁性基体上非导电复盖层厚度的涡流检测 |
| BS 5411 Pt.9-84 | 非磁性基体上镀镍层厚度的磁性检测方法 |
| BS 5411 Pt.11-84 | 磁性基体上非磁性复盖层厚度的磁性测量方法 |
| BS 6072-81(1986) | 缺陷的磁粉检验方法(81年版在INDT 84-2) |
| BS 6404-5-1995 |
磁性材料 永磁(硬磁)材料 磁性能测量方法 Magnetic materials - Permanent magnet (magnetically hard) materials - Methods of measurement of magnetic properties |
| BS DD ENV 50166-1-1995 |
人体电磁场照射 低频(0 Hz 至 10 kHz) Human exposure to electromagnetic fields - Low frequency (0 Hz to 10 kHz) |
| BS DD ENV 50166-2-1995 |
人体电磁场照射 高频(10 kHz 至 300 GHz) Human exposure to electromagnetic fields - High frequency (10 kHz to 300 GHz) |
| BS M35 | 材料及工件的磁粉检验 |
| BS EN 1290-1998 |
焊缝的无损检验 焊缝的磁粉检验 Non-destructive examination of welds - Magnetic particle examination of welds |
| BS EN 1291-1998 |
焊缝的无损检验 焊缝的磁粉检验 验收等级 Non-destructive examination of welds - Magnetic particle testing of welds - Acceptance levels |
| BS EN 1330-5-1998 | 无损检测术语-涡流检测 Non-destructive testing - Terminology - Terms used in eddy current testing |
| BS EN 1369-1997 | 铸造-磁粉检验 Founding - Magnetic particle inspection |
| BS EN 10228-1-1999 | 锻钢件无损检测-磁粉检验 Non-destructive testing of steel forgings - Magnetic particle inspection |
| BS EN 10246-1-1996 |
钢管的无损检测-铁磁性无缝与焊接（埋弧焊除外）钢管验证水压试验的自动电磁检测 Non-destructive testing of steel tubes - Automatic electromagnetic testing of seamless and welded (except submerged arc welded) ferromagnetic steel tubes for verification of hydraulic leak-tightness |
| BS EN 10246-2-2000 | 钢管的无损检测-奥氏体与奥氏体-铁素体无缝与焊接（埋弧焊除外）钢管验证水压试验的自动涡流检测 |
| BS EN 10246-3-2000 |
钢管的无损检测-探测无缝与焊接（埋弧焊除外）钢管不完整性的自动涡流检测 Non-destructive testing of steel tubes - Automatic eddy current testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of imperfections |
| BS EN 10246-4-2000 |
钢管的无损检测-铁磁性无缝钢管横向不完整性自动全圆周磁探头/漏磁检测 Non-destructive testing of steel tubes - Automatic full peripheral magnetic transducer/flux leakage testing of seamless ferromagnetic steel tubes for the detection of transverse imperfections |
| BS EN 10246-5-2000 | 钢管的无损检测-铁磁性无缝与焊接（埋弧焊除外）钢管纵向不完整性自动全圆周磁探头/漏磁检测 Non-destructive testing of steel tubes - Automatic full peripheral magnetic transducer/flux leakage testing of seamless and welded (except submerged arc-welded) ferromagnetic steel tubes for the detection of longitudinal imperfections |
| BS EN 10246-12-2000 |
钢管的无损检测 探测无缝和焊接铁磁钢管表面不完整性的磁粉检验 Non-destructive testing of steel tubes - Magnetic particle inspection of seamless and welded ferromagnetic steel tubes for the detection of surface imperfections |
| BS EN 10246-18-2000 |
钢管的无损检测 探测无缝和焊接铁磁钢管管端层状不完整性的磁粉检验 Non-destructive testing of steel tubes - Magnetic particle inspection of tube ends of seamless and welded ferromagnetic steel tubes for the detection of laminar imperfections |
| BS EN 12084-2001 |
无损检测-涡流检测-一般原理与指南 Non-destructive testing - Eddy current testing - General principles and guidelines |
| BS EN ISO 2178-1995 |
磁性基体上非磁性涂层的厚度测量-磁性法 Non-magnetic coatings Ｏn magnetic substrates - Measurement of coating thickness - Magnetic method |
| BS EN ISO 2360-1995 |
非磁性金属基体上非导电涂层的厚度测量-涡流法 Non-conductive coatings Ｏn non-magnetic basis me |
| BS EN ISO 2361-1995 |
磁性和非磁性基体上镍镀层的厚度测量-磁性法 Electrodeposited nickel coatings Ｏn magnetic and non-magnetic substrates - Measurement of coating thickness - Magnetic method |
| BS EN ISO 9934-1-2001 | 无损检测 磁粉检测 一般原理 Non-destructive testing - Magnetic particle testing - General principles |
| BS EN ISO 9934-2-2002 | 无损检测 磁粉检测 探测介质 Non-destructive testing - Magnetic particle testing - Detection media |
| BS EN ISO 9934-3-2002 | 无损检测 磁粉检测 设备 Non-destructive testing - Magnetic particle testing - Equipment |
| 法国: | |
| NF A04-101-64 | 冶金产品磁粉检测(磁悬液检测) |
| NF A04-121-74 | 钢制长条形制品表面缺陷的磁粉检验 |
| NF A04-193-1997 | 铸造 磁粉检验 Founding - Magnetic particle inspection. |
| NF A05-115-1999 | 铜及铜合金 管子的涡流检测 Copper and copper alloys. Eddy current test for tubes. |
| NF A09-020-5-1998 |
无损检测术语 第5部分:涡流检测 Non-destructive testing. Terminology. Part 5 : terms used in Eddy Current testing. |
| NF A09-125-82 | 冶金制件磁粉探伤的一般原理 |
| NF A09-160-2001 |
无损检测 涡流检测 一般原理和指南 Non-destructive testing - Eddy current testing - General principles and guidelines. |
| NF A09-590-1-2002 |
无损检测 磁粉检测 第1部分:一般原理 Non-destructive testing - Magnetic particle testing - Part 1 : general principle. |
| NF A09-590-3-2002 |
无损检测 磁粉检测 第3部分：设备 Non-destructive testing - Magnetic particle testing - Part 3 : equipment. |
| NF A49-871-81 | 铁磁性钢管纵向缺陷的探头检漏法检测 |
| NF A49-872-83 | 穿过式线圈法的钢管涡流探伤 |
| NF A49-875-1-1996 | 钢管的无损检测 第1部分:无缝和焊接铁磁钢管(埋弧焊除外)验证水压试验的自动电磁检测 Non destructive testing of steels tubes. Part 1 : automatic electromagnetic testing of seamless and welded (except submerged arc welded) ferromagnetic steel tubes for verification of hydraulic leak-tightness. |
